Posted in

Can HIR2/9012 handle high voltages?

Hey everyone, if you’ve been in the semiconductor or power electronics game for even a minute, you’ve probably run into the HIR2/9012 lineup—and one question comes up at least once a week: Can these chips handle high voltages? As a supplier who’s worked with these parts for years, I’m here to break this down straight, no corporate jargon, no fluff. Let’s cut to the chase. HIR2 / 9012

First, let’s get on the same page about what HIR2/9012 actually are. They’re a series of high-speed, optocoupler (optical isolator) chips that we supply every day. Optocouplers, for those who might not know, separate two electrical circuits with light—so one side (low-voltage control, like a microcontroller) and the other (high-voltage power, like a motor driver or inverter) don’t share a ground. That’s the whole point, right? Isolation keeps your low-voltage side safe from spikes, shorts, or noise on the high-voltage side. So naturally, voltage handling is non-negotiable here.

Now, let’s talk high voltages. What counts as “high” for HIR2/9012? A lot of people throw around numbers like 120V, 240V, even 480V for industrial or consumer power gear. But the real spec to look at isn’t just the max voltage the chip sees across its pins—it’s two critical ratings: the isolation voltage (often called BV_{ISO}, or dielectric strength) and the working voltage (V_{IORM}, the maximum continuous voltage you can apply without degrading the chip).

For our HIR2/9012 models, here’s the hard data we stand behind: The isolation voltage (that’s the voltage between the input LED side and the output phototransistor side) is rated at 5000VAC for 1 minute. That’s a standard industry test to make sure the insulation between the two sides doesn’t break down. The working voltage? We list V_{IORM} at 1414V peak, which works out to 1000V RMS continuous. Wait, let’s do the math quick—1000V RMS is what you get from most residential outlets, and 1414V peak is the highest voltage you’ll see on a 480V three-phase system, right? That’s not a coincidence. We engineered these to handle the voltages most users actually run into, not some unrealistic lab number.

But here’s where people mess up: They’ll see a 5000V isolation spec and think, “Cool, I can hit 5000V all day.” No. That 5000V is a one-minute proof test, not a continuous operating level. If you run 5000V through the optocoupler for more than a few seconds, you’re gonna break the dielectric (the insulating material between the two sides) and the chip will fail. We’ve seen this happen a couple times—customers test at 5000V for 10 minutes, think the spec is wrong, but no, that’s not how it works. Always stick to the working voltage (1000V RMS for most HIR2/9012 variants) for long-term use.

Now, let’s get into real-world use cases because specs are useless if they don’t apply to what you’re building. If you’re making a home appliance—like a smart oven, or a fridge with a motor controller—your high-voltage side is probably 120V or 240V. That’s way under the 1000V V_{IORM}, so these chips will handle that no problem. If you’re doing industrial stuff—like a small CNC machine, a solar inverter, or a motor drive for a warehouse crane—you might be dealing with 480V three-phase. The peak here is ~1350V, which is just barely under the 1414V peak rating. Wait, so that’s okay? Yeah, as long as you’re not running continuous peak voltage—most industrial systems have small voltage spikes that happen during startup, not constant peak. We have tons of customers running HIR2/9012 in 480V systems with zero issues, even after 5+ years of use.

But what if someone needs higher? Like, say, a 600V or 1000V DC power supply, or a 600V AC line? Let’s say 600V RMS. That’s still under 1000V, so still good. Wait, what about 1500V? You’re gonna need a different part, not the HIR2/9012. Our HIR2/9012 line tops out at 1414V peak. If you’re going higher than that, we can point you to our other optocoupler series that have 7000V isolation and 2500V V_{IORM}—but that’s not what HIR2/9012 is for. Don’t force a part to do something it’s not designed for, that’s how you get downtime.

Another thing people forget: Creepage and clearance. What’s that? Creepage is the distance between two conductors (like input and output pins) along the surface of the chip package, and clearance is the air gap between them. For high-voltage apps, if those gaps are too small, even if the dielectric is good, you can get arcing between the pins. Our HIR2/9012 is packaged in DIP-8 and SOP-8 packages that meet IEC 60335 and UL 60950 standards for creepage and clearance up to 1000V. That means you don’t have to design extra gaps on your PCB if you’re staying under 1000V—we already built that into the part. If you’re going over 1000V, you’ll need to adjust your PCB layout, but that’s a separate issue from the chip itself.

Let’s talk about common mistakes we see customers make with HIR2/9012 and high voltages. Number one: Under-rating the input side. Wait, the input side is low-voltage, right? But if your control side has a spike that bleeds over? No, wait, no—the other way: the output side. If the high-voltage side has a voltage spike that couples back through the optocoupler? No, actually, a big mistake is using the wrong resistor on the output. The output of the HIR2/9012 is a phototransistor, so you use a pull-up resistor. If that pull-up resistor is too small, you let too much current into the transistor, which can make it break down at lower voltages than the spec. We recommend a 1kΩ to 10kΩ pull-up resistor for most high-voltage apps—way more than that and you get slow switching, way less and you risk overloading the transistor.

Another mistake: Not derating for temperature. Oh right, semiconductors don’t work the same at 25°C as they do at 100°C. If your device is running hot—like a power supply in a server rack, or a motor drive in a hot warehouse—your max working voltage goes down. For HIR2/9012, at 85°C (max operating temp), you can still run 800V RMS, which is still enough for most apps. If you’re at 100°C, that drops to ~700V RMS, so you’d want to make sure your system doesn’t go over that. We always remind customers to check the derating curve in the datasheet—don’t just use the 25°C number, that’s for room temp only.

Now, let’s get specific about our supply. We don’t just sell generic HIR2/9012 chips—we test every batch before it leaves our warehouse. A lot of cheap suppliers out there cut corners on isolation testing, so you might get a chip that’s rated 5000V but only handles 2000V. We test every lot for 5000VAC dielectric strength, and we run voltage cycling tests to make sure they hold up over time. Last year, we had a customer who tried a cheaper alternative from another supplier, and their chips failed after 3 months in a 480V inverter. They switched to our HIR2/9012, and they haven’t had a single failure since. That’s the difference between a reliable supplier and someone just moving parts.

Wait, let’s address a question we get all the time: Can HIR2/9012 handle AC vs DC high voltages? Short answer: The isolation spec works for both, but the working voltage is rated for AC RMS. Why? Because AC has a peak voltage that’s higher than the RMS—1000V RMS AC is 1414V peak, which is exactly the V_{IORM} we list. For DC, since it’s constant, you can run up to 1000V DC, but we derate that slightly because DC puts more stress on the dielectric than AC. So if you’re using DC power, aim for 800V max, just to be safe. That’s a little detail that’s buried in the datasheet, but we make sure to tell every customer about it.

Is there a time when HIR2/9012 can’t handle high voltages? Absolutely. If you’re designing a EV charger that works with 800V DC, HIR2/9012 isn’t the right fit. If you’re building a high-voltage test bench that runs 2000V continuously, you need a different part. But for 90% of the stuff our customers build—residential appliances, small industrial drives, solar micro-inverters, home automation gear—these chips work perfectly. We’ve even had customers use them in electric bike controllers, which run up to 72V DC—way under our 1000V rating, and they hold up great even in rain or extreme temperatures.

Let’s wrap this up with a clear takeaway: HIR2/9012 can handle high voltages, but only if you use them within their specs. Stick to 1000V RMS continuous (or 1414V peak) for AC, 800V for DC, check the derating for temperature, make sure your PCB has enough creepage/clearance, and avoid the common mistakes like too-small pull-up resistors. We’ve been supplying these parts for over a decade, and we stand by their voltage handling every single day.

If you’re working on a project and you’re not sure if HIR2/9012 is right for your voltage needs, or you need bulk orders with fast lead times, hit us up to chat. We can send you free samples, walk you through the datasheet, even help you troubleshoot if you’re having voltage issues in your design. Don’t waste time guessing with cheap no-name parts—our HIR2/9012 are tested, reliable, and made for exactly the kind of high-voltage apps you’re building.

H7 LED Bulbs References

  1. HIR2/9012 Series Datasheet, Standard Semiconductor Components, 2023.
  2. IEC 60335, Safety of Household and Similar Electrical Appliances, 2021.
  3. UL 60950, Information Technology Equipment Safety, 2022.
  4. Power Electronics Design Guidelines for Optocoupler Isolation, Semiconductor Industry Association, 2022.

Guangzhou Ruiandsion Lighting Technology Co., Ltd.
Guangzhou Ruiandsion Lighting Technology Co., Ltd. is well-known as one of the leading hir2 / 9012 manufacturers and suppliers in China. If you’re going to wholesale high quality hir2 / 9012, welcome to get free sample from our factory. Also, customized service is available.
Address: Building 9,Jiuwu Technology Park,No.6 Baishan Road
E-mail: Ruiandsion@gmail.com
WebSite: https://www.ledruiandsion.com/