If you’ve ever stood in a water treatment lab or walked the production floor of a membrane manufacturing facility, you know that hydrophilic PES (polyethersulfone) membranes aren’t just another filter option—they’re a workhorse. I’ve been supplying these membranes for over a decade, and the question I get asked most often isn’t “How do they work?” but “What’s their rejection rate for different solutes?” It’s a fair question, because rejection rate isn’t a one-size-fits-all number; it changes with solute size, charge, concentration, and even operating conditions. Let’s break this down based on real data, on-the-job experience, and the tests we run every day at our facility. Hydrophilic PES Membrane

First, let’s get a quick refresher on what makes hydrophilic PES different from regular PES. Most unmodified PES is hydrophobic, which means water beads up on its surface, slowing flow and letting small, non-polar solutes slip through. We tailor ours with a hydrophilic coating that’s both chemically stable and pore-consistent—no leaching, no degradation, even when exposed to harsh pH ranges or hot water. That consistency is key when it comes to rejection rates, because a membrane with evenly sized pores will reject solutes more reliably than one with warped or irregular holes.
Let’s start with the smallest solutes we test, and the ones that give customers the most headaches: dissolved ions. Salts like sodium chloride (NaCl) and magnesium chloride (MgCl₂) are everywhere in water—reverse osmosis (RO) is usually the go-to for complete salt removal, but our hydrophilic PES membranes are often used in pre-treatment or in applications where full desalination isn’t needed. Our data from 10,000+ tests over the last five years shows that NaCl rejection hovers around 10–15% at standard operating pressures (15 psi, 25°C) and a 1000 ppm feed concentration. MgCl₂, with a higher charge and slightly larger hydrated radius, hits 20–25% in the same conditions. I’ve seen customers expect these numbers to be higher, especially when they’re comparing to RO membranes, so it’s important to set that baseline. These low rejection rates are actually intentional—we design our membranes to let small monovalent ions pass through while retaining larger, more problematic solutes, which cuts down on energy costs compared to full RO.
Next up, small organic molecules. This is where hydrophilic PES shines, especially for what’s called “emerging contaminants”—the trace chemicals like pharmaceuticals, pesticides, and industrial byproducts that regulators are cracking down on now. Let’s take three common ones: bisphenol A (BPA), atrazine, and ibuprofen. In our lab, BPA (molecular weight 228 g/mol) has a rejection rate of 85–90%, atrazine (215 g/mol) hits 80–85%, and ibuprofen (206 g/mol) is around 75–80%. What’s interesting about these is that rejection isn’t just about size—charge plays a role here too. Ibuprofen is negatively charged at neutral pH, and our hydrophilic membrane has a slight negative surface charge as part of the coating, so there’s an extra electrostatic repulsion that pushes ibuprofen away from the pores. That’s why its rejection is a little higher than a similarly sized neutral solute would be, and it’s one of the reasons our membranes are used so often in drinking water treatment for these compounds. I remember a customer from a small municipal plant telling us they switched to our hydrophilic PES after their old hydrophobic membranes only removed 50% of atrazine—those extra 30% made all the difference for them to meet EPA standards.
Moving to medium-sized solutes: proteins. This is a big one for biotech and pharmaceutical manufacturing, where retaining proteins while letting buffer salts pass is critical for purification. Our hydrophilic PES membranes are widely used in tangential flow filtration (TFF) for antibody purification, so we have reams of data here. Let’s take monoclonal antibodies (mAbs), which are around 150,000 g/mol, and bovine serum albumin (BSA), which is 66,000 g/mol. For mAbs, rejection rate is 99.5%+ when using a 0.1 µm or 0.22 µm pore size membrane—so close to 100% that you’d be hard-pressed to measure the tiny amount that slips through. For BSA, rejection is around 98–99%. Why is that? BSA’s size is right at the cutoff for our typical TFF membrane pores, so a small number of molecules can slip through, but the surface charge adds another layer of retention. I once worked with a biotech startup that was struggling with BSA leakage during their early antibody purification runs. They were using a competitor’s membrane that only had 95% BSA rejection, which threw off their yield by 10%. Switching to our hydrophilic PES got them to 98.8% rejection, and they scaled their process within six months. That’s the kind of real impact these numbers have on customers’ bottom lines.
Then there are larger colloids and particles: things like bacteria, viruses, and suspended solids. This is where hydrophilic PES really lives up to its reputation as a reliable filter. Bacteria are around 0.5–5 µm in size, and even our largest microfiltration (MF) hydrophilic PES membranes (0.45 µm and 0.22 µm) have a rejection rate of 99.99% for common bacteria like E. coli and S. aureus. That’s why these membranes are used for sterile filtration in labs and pharmaceutical cleanrooms alike. For viruses, which are much smaller (20–200 nm), our 0.05 µm ultrafiltration (UF) membranes have a rejection rate of 99.9% for viruses like norovirus and bacteriophage MS2. I’ve seen these membranes tested in wastewater reclamation projects, where they’re used to remove pathogens before the water is reused for irrigation—they consistently hit that high rejection rate even when the feed water has fluctuating levels of suspended solids.
Now, it’s not all black and white. Rejection rates can shift, and it’s important to talk about the factors that change them, because that’s what customers often don’t anticipate. First, pore size: if you go from a 0.22 µm MF membrane to a 0.01 µm UF membrane, rejection for all solutes goes up, obviously, but flow rate goes down too. We help customers balance that tradeoff based on their needs. Second, pH and charge: if you adjust the pH of your feed water, you can change the charge of both the solute and the membrane, which affects rejection. For example, if you’re filtering a positively charged protein, making the pH more acidic will make the protein more positively charged, and our membrane’s slight negative charge will create more repulsion, boosting rejection. Third, concentration: if you have a very high concentration of solute, especially proteins, they can start to build up on the membrane surface (called fouling), which acts like an extra layer of filtration and can actually increase rejection rate—at least temporarily. Over time, though, fouling can reduce flow and even damage the membrane, so we work with customers on pre-treatment steps to minimize that. Fourth, operating pressure and temperature: higher pressure will push more small solutes through, lowering rejection, while higher temperatures can make solutes more soluble and change their size, too. All of our rejection data is tested at standard 25°C and 15 psi, and we adjust recommendations for customers operating in different conditions.
I also want to address a common myth: that all hydrophilic PES membranes perform the same. That couldn’t be further from the truth. During the pandemic, we saw a surge in demand for sterile filtration membranes, and we tested 12 different off-the-shelf membranes for bacteria rejection. Half of them had rejection rates below 99.5%, which is the minimum we require for our products. The difference came down to the coating process—we use a proprietary, covalently bonded hydrophilic layer that doesn’t leach into the feed water, so the pore size stays consistent even after hundreds of hours of use. Other manufacturers use a blended coating that can degrade over time, leading to larger pores and lower rejection rates. That’s the kind of detail that makes our membranes stand out, and it’s why we share all our test data with customers before they place an order.
Let’s put this all together in a quick reference guide for the most common solutes customers ask about, based on our average test results at standard operating conditions:
- Monovalent ions (NaCl, KCl): 10–15% rejection
- Divalent ions (MgCl₂, CaCl₂): 20–25% rejection
- Small organic contaminants (BPA, atrazine, pharmaceuticals): 75–90% rejection, depending on size and charge
- Proteins (BSA, mAbs): 98–99.9%+ rejection, based on size and pore size
- Bacteria (E. coli, S. aureus): 99.99%+ rejection (0.22 µm membrane)
- Viruses (MS2, norovirus): 99.9% rejection (0.05 µm membrane)
If you’re here, chances are you’re evaluating a hydrophilic PES membrane for a specific application—whether that’s lab sterile filtration, biotech protein purification, drinking water treatment, or industrial wastewater processing. The rejection rate isn’t just a number on a spec sheet; it’s what will make your process work, keep your product safe, and meet your regulatory requirements. We don’t just sell membranes—we work with customers to test their specific solutes, adjust operating parameters, and make sure they get the rejection rate they need without wasting money on over-engineered systems.

If you’re ready to talk about your project, we can send you a free sample for testing, or walk through our lab data for the exact solutes you’re filtering. Don’t waste time guessing at rejection rates—reach out so we can help you find the right membrane for your needs.
Hydrophilic PES Membrane References
- Baker, R. W. Membrane Technology and Applications, 3rd ed. Wiley, 2012.
- Van der Bruggen, B., et al. “Rejection of organic micropollutants by ultrafiltration and nanofiltration membranes.” Journal of Membrane Science, vol. 225, no. 1-2, 2003, pp. 77–89.
- Zulewska, J., et al. “Hydrophilic modification of polyethersulfone membranes for protein purification.” Separation and Purification Technology, vol. 72, no. 2, 2010, pp. 191–198.
- EPA. “Drinking Water Contaminants: Occurrence and Exposure Assessment.” U.S. Environmental Protection Agency, 2021.
- Lucero, M., et al. “Performance of hydrophilic PES microfiltration membranes for pathogen removal in wastewater reclamation.” Water Research, vol. 145, 2018, pp. 212–220.
Nantong Delta Filtration Material Co., Ltd.
Nantong Delta Filtration Material Co., Ltd. is known as one of the most professional hydrophilic pes membrane manufacturers and suppliers in China. If you’re going to buy high quality hydrophilic pes membrane with competitive price, welcome to get more information from our factory.
Address: 2811, Block B, Zhongnan CBD, Nantong, Jiangsu, China
E-mail: info@delta-filtration.com
WebSite: https://www.delta-filtration.com/