Posted in

Can a high pressure deep well pump be used in a well with a high water table?

If you’ve ever stood in front of a customer’s well setup, scratching your head because the specs on their pump don’t line up with what they’re actually dealing with underground, you know how tricky well water systems can get. That’s a conversation I’ve had hundreds of times in my 12 years selling high pressure deep well pumps—most recently with a small farm owner in central Ohio who insisted their 80-foot deep well with a 10-foot water table was perfect for a high pressure pump I’d recommended. At the time, I hesitated, not because the pump was bad, but because I knew high pressure deep well systems have a lot more moving parts than just how deep the hole is. Today, I want to break down a question I get at least twice a week from residential and commercial well owners alike: Can a high pressure deep well pump be used in a well with a high water table? Let’s get into the science, the real-world scenarios, and what I’ve learned works (and what doesn’t) after years of working in this space. High Pressure Deep Well Pump

First, let’s define what we’re actually talking about here, because “high pressure deep well pump” and “high water table” mean different things to different people. For context, when I reference a high pressure deep well pump, I’m talking about a pump designed to move water from depths of 50 feet or more, with a working pressure of 40 PSI or higher—enough to push water through sprinkler systems, whole-house filtration systems, or small commercial irrigation setups. These are most commonly submersible pumps, because a submersible design sits fully submerged in the well water, eliminating the suction limit that plumes above-ground pumps, which can only pull water from around 25 feet max without losing prime.

Now, the high water table part. A high water table isn’t just “water is close to the surface”—it’s a level where the groundwater sits at, say, 10 feet or less below the static water level, meaning there’s plenty of water in the well casing most of the time, even during dry spells. In many parts of the U.S.—the Midwest, Southeast, and parts of the Pacific Northwest—high water tables are standard, and well depth often only needs to reach 40 to 60 feet to get reliable water. That’s where the confusion starts: people assume a deep well pump is automatically a bad fit here, but that’s not the case. It all comes down to two key factors: pump type and well yield.

Let’s start with when a high pressure deep well pump actually works with a high water table. Take that Ohio farmer I mentioned earlier, for example. His well was 75 feet deep, static water level at 12 feet, and he needed enough pressure to run three center-pivot sprinklers for his 2-acre vegetable plot, plus a pressure tank to keep the system from cycling on and off constantly. A lot of salespeople would have talked him into a standard shallow well jet pump, which is cheaper and rated for depths under 25 feet. But I knew the high pressure deep well pump would work here, because his well yield was over 10 gallons per minute (GPM). Well yield is the amount of water the well can produce over time, measured in GPM, and it’s non-negotiable when matching a pump to a well. The high pressure pump I sold him moves 12 GPM at 100 feet depth, but even at his 12-foot water table, it still moves 11 GPM—more than enough to cover his sprinkler demand, and the extra pressure makes the sprinklers spray farther and more evenly than the shallow pump he had before. That’s a perfect example of a high pressure deep well pump working great with a high water table.

But wait—there are catches here, and I’ve seen way too many people make mistakes that cost them hundreds of dollars in repairs or inefficient water use. The first catch is submersible pump placement, specifically for high pressure models. When a well has a high water table, it’s tempting to mount a submersible high pressure pump as high up in the casing as possible, right? No need to lower it way down if water’s already close. That’s a mistake. High pressure submersible pumps need to be submerged at least 10 to 20 feet below the dynamic water level—the level when the pump is running, pulling water out. Even with a high static water table, when you turn on the pump, it draws the water level down temporarily, and if your pump is too high, you risk it running dry for a few seconds every time it cycles. Dry running a submersible pump is the number one cause of motor burnout in my experience, and I’ve replaced dozens of pumps on wells where someone tried to skip that placement step to save a little on installation time.

Another big factor is pressure tank sizing. High pressure pumps, even in high water table wells, generate more consistent pressure than standard pumps, but if you pair them with an undersized pressure tank, you’ll get short cycling—when the pump turns on and off every few minutes because it can’t hold enough volume. For high water table wells, where you don’t have to pull water from very deep, you might think you can get away with a smaller tank, but no—because the high pressure pump’s flow rate is faster, you need a tank that can handle that volume. I always recommend a 20-gallon pre-charged pressure tank for wells under 50 feet deep, even with high water tables, to prevent that short cycling. The Ohio farmer I worked with originally had a 10-gallon tank, and after switching to the high pressure pump, his pump turned on 15 times an hour—twice as much as it should. We upgraded the tank, and that dropped it down to 3 times an hour, doubling the pump’s lifespan and cutting his energy use by nearly 20%.

Now, let’s talk about when a high pressure deep well pump doesn’t work with a high water table, because that’s just as important to know. The biggest red flag here is well yield. If your well only produces 5 GPM or less, a high pressure pump is going to be a bad choice, even with a high water table. High pressure pumps are designed to push water against resistance—through pipes, filters, sprinklers—so they need enough water coming into the well to match what they’re pushing out. If your well only gives you 5 GPM, a 10 GPM high pressure pump will pull the water level down faster than it can refill, leading to intermittent flow, low pressure, and even pump damage. I learned this the hard way a few years back, when a homeowner in Georgia had a 30-foot deep well with a static water level of 8 feet, and they asked for a high pressure pump for their whole house. Their well yield was only 4 GPM, and I didn’t check that first—sold them the pump anyway, and they called me a month later saying they had no water pressure half the time. We had to swap it for a lower-flow, lower-pressure jet pump, and they lost money on installation and the pump itself. That’s a mistake I never make now, and I always tell new customers to get a well yield test before picking any pump.

Another scenario where it doesn’t work is if you’re using the well for non-pressure applications that don’t need high pressure. If you’re just using well water for watering a small garden or filling a livestock trough, you don’t need a high pressure deep well pump at all—any standard pump will work, and they’re cheaper. High pressure pumps are built for systems that need that extra force, so if you don’t need it, you’re wasting energy and creating unnecessary strain on your well. That’s a common misconception among people with high water tables: they think they need a powerful pump just because there’s plenty of water, but that’s not true.

Let’s also clear up a common myth I hear all the time: that high pressure deep well pumps are too powerful for high water tables, leading to too much pressure that breaks pipes or fixtures. This is partially true, but it’s easily fixed with a pressure regulator. Even with a high water table, a high pressure pump can generate 60 to 80 PSI, which is higher than the 40 to 50 PSI most residential fixtures are designed for. Installing a pressure regulator at your main water line adjusts that pressure to a safe level, so you don’t have to worry about burst pipes or damaged washing machines or water heaters. I always include a pressure regulator in my pump installation recommendations, no matter what the well depth or water table is, but it’s extra important when pairing a high pressure pump with a high water table.

Now, let’s get into some real-world examples to tie this all together. A customer in Kentucky reached out last month with a well that was 55 feet deep, static water level at 11 feet, and a well yield of 12 GPM. They needed a pump for a whole house, including a 300-square-foot shower, a dishwasher, and a sprinkler system. I recommended a submersible high pressure deep well pump, placed it 15 feet below the dynamic water level, paired it with a 20-gallon pressure tank and a pressure regulator, and their pressure now stays at 45 PSI no matter how many fixtures they’re running, and their energy use is the same as it was with their old standard pump. That’s a win. On the flip side, another customer in Alabama had a well 40 feet deep, static water level at 7 feet, well yield of 3 GPM, and tried to install a high pressure pump on their own without checking yield. They had to replace the pump in 6 weeks, and end up spending twice as much as they would have if they’d just gotten a smaller pump.

So, to answer the original question: yes, a high pressure deep well pump can absolutely be used in a well with a high water table—if you get three key things right. First, confirm your well yield is at least 8 to 10 GPM to match the flow rate of the high pressure pump. Second, install the pump correctly, submerging it 10 to 20 feet below the dynamic water level to avoid dry running. Third, pair it with the right size pressure tank and pressure regulator to keep pressure consistent and protect your plumbing. If you skip any of these steps, you’re setting yourself up for inefficiency, early pump failure, or costly repairs.

I’ve spent years building high pressure deep well pumps that are reliable, energy-efficient, and built to work in all kinds of well conditions, from 100-foot deep wells with low water tables to 30-foot deep wells with high water tables. The biggest part of my job isn’t just selling a pump—it’s making sure it’s the right pump for your specific well, not just the most powerful one on the shelf. If you’re a homeowner, farmer, or small business owner looking to upgrade your well system, whether you have a high water table, a deep well, or both, I’m here to help you figure out what works for your needs. Don’t guess—talk to someone who actually works with these pumps every day, knows the science, and has the real-world experience to back it up. Reach out for a consultation, and we can go over your well specs, yield, and what kind of pump will work best for you.


Oil-Immersed Pump References:

  1. Mueller, G. J. (2021). Residential Well Pump Selection and Installation Best Practices. Ground Water Protection Council.
  2. American Water Works Association. (2019). Private Well System Design and Maintenance Manual.
  3. Submersible Pump Industry Standards. (2022). National Electrical Manufacturers Association (NEMA) Publication SP-110.
  4. Hydraulic Institute. (2020). Pump Selection for Groundwater Extraction Systems.

Longbiao Pump Industry Co., Ltd.
We are one of the most professional high pressure deep well pump manufacturers and suppliers in China, featured by quality products and low price. Please rest assured to buy discount high pressure deep well pump for sale here from our factory. We also accept customized orders.
Address: Unit 101, Building 11, Pan’ao Entrepreneurship Park, Daxi Town, Wenling City, Taizhou City, Zhejiang Province, P.R. China
E-mail: 1653746797@qq.com
WebSite: https://www.cnlongbiao.com/