A few weeks back, I got a frantic Friday evening call from a long-time residential customer, Maria, who’s been buying our submersible sump pumps for her finished basement for three years. She was pacing around her house at 7 PM, water pooling around her washing machine, because her toilet’s pump—wait, let’s get this right, Maria was calling the inline pump that feeds her upstairs bathroom toilet’s flush system, not the sump—had locked up mid-cycle. By the time I drove 20 minutes to her place, I’d seen this exact headache a dozen times, and I’ve been in the pump supply game for 12 years, so I knew exactly how to break it down simply, no fancy engineering jargon. The best part? She fixed it herself in 20 minutes, saved a $150 plumber call, and came back the next week to pick up a spare impeller kit for when it happens again. That’s the whole point of this post: running a toilet pump doesn’t have to be a crisis, and with a little know-how, you can fix most common issues before you need to call for backup. Pump

First, let’s get clear on what a toilet pump actually is, because a lot of people mix this up with the standard gravity-fed toilet they’ve had since they were a kid. Gravity toilets work just fine for most homes, but if you’re in a basement, a low-lying home on a slab with no slope for waste lines, or an RV or small commercial space, you’re working with a macerating toilet pump, often called a “toilet pump” colloquially. These little workhorses take the waste and water from your toilet, macerate it (grind it up into a slurry), then pump it up and out to your main sewer line or septic tank—no slope required. The “running” part people complain about is usually either the pump running nonstop when it shouldn’t, or it won’t run at all when you flush. We’re covering both scenarios here, since those are the two most common “toilet pump running” complaints we get from our customers.
Before we dive into fixes, the first rule of working with any pump—especially one that handles waste—is safety. I always tell my team to remind customers this, and Maria would’ve listened if I hadn’t had to rush over: turn off the power first. That’s non-negotiable. Most toilet pumps are powered by 110V outlets, usually tucked behind the toilet or in the basement near the wall. Unplug it, or flip the circuit breaker for that outlet in your electrical panel. Don’t just trust the switch on the pump—we’ve had customers get shocked because the switch was faulty. Also, keep a roll of paper towels and a pair of rubber gloves handy, because there’s almost always a little residual water, and we’re dealing with waste, so hygiene first.
Now, the most common “running toilet pump” issue is constant cycling: it turns on for 10 seconds, off for 2, on again, nonstop. Nine times out of 10, that’s not a bad pump—it’s a tiny clog or a misaligned float. Let’s start with the float, because that’s the easiest thing to check first. The float is the plastic (or sometimes metal) rod on the side of the pump housing that rises and falls with the waste level, telling the pump when to turn on and off. If it’s stuck in the upright position, the pump thinks there’s way too much waste, so it keeps trying to empty the tank nonstop. That’s exactly what Maria had—her kid had knocked the float when he was grabbing a toy under the toilet. To check it, after you’ve powered off the pump, gently lift the float up and down by hand. It should move smoothly, no sticking. If it’s stuck, wiggle it loose, and if it’s really dirty (which happens over time, from waste residue), wipe it down with a mild disinfectant. If it still sticks, a quick squirt of silicone lubricant (not oil—oil attracts more gunk) on the pivot point will fix that. For our customers, we always include a small bottle of silicone lube with every pump we sell, because this is such a common issue.
If the float moves fine, the next culprit is a small clog in the pump’s inlet or the check valve. The inlet is the opening where waste flows into the pump, and the check valve is the one-way valve that keeps water from flowing back into the pump after it’s pumped out, which prevents constant cycling. For clogs here, first, you’ll need to empty the pump housing to get to it. Once power’s off, turn off the water supply to the toilet (that’s the little valve behind the toilet on the wall), flush the toilet to get most of the water out, then grab a small bucket to catch the remaining water in the pump housing. Disconnect the inlet hose (it’s usually a plastic or metal clamp, just loosen it with a screwdriver) and look inside. A lot of times, there’s a tiny piece of toilet paper, a cotton swab, or even a small toy part stuck here. Don’t use a wire hanger or anything sharp to dig it out—you can scratch the inlet and cause leaks. Use a pair of tweezers or a flat plastic scraper, and if the clog is deeper in the pump, you can take out the impeller cover (most toilet pumps have a easy-access cover that takes two screws to remove) to get to it. Once the clog is out, rinse it with warm water, reconnect everything, turn the water back on, plug the pump in, and test it by flushing. For 70% of the constant-running calls we get, that’s all it takes.
The second big “running toilet pump” issue is the pump not running at all, which people often call “running” because it’s making a humming noise nonstop, like it’s trying but can’t turn on. That’s usually a seized impeller, which is the little spinning part inside the pump that pushes the waste out. Impellers get seized when there’s debris in the pump, or if the pump’s been sitting unused for a long time (like in a vacation home that’s closed for the winter). Let’s walk through fixing that, because this is another super common issue. Again, start with power off and rubber gloves on. Remove the pump from the housing—most submersible toilet pumps just lift out, since they’re designed to sit in a little pit or basin behind the toilet. Once it’s out, lay it on a towel so you don’t scratch the motor housing. The impeller is usually covered by a plastic or metal plate that’s held on by 2-4 small screws. Unscrew that plate gently, and look at the impeller. If it’s seized, it won’t spin when you try to turn it with your finger. Don’t force it—you can break the impeller. Instead, put a drop of warm water and a tiny bit of dish soap on it, let it sit for 2 minutes, then gently work it back and forth until it spins freely. If that doesn’t work, a small bit of rubbing alcohol will loosen gunk buildup. If the impeller is cracked or broken, that’s when you’ll need a replacement—something we keep in stock at all times, because this is such a common part replacement. For most residential customers, we sell replacement impellers for under $20, and we’ll ship them the same day if they order before 3 PM.
Now, what about more serious issues? If you’ve checked the float, cleared the clogs, and the impeller is spinning freely, and the pump still won’t run or runs nonstop, that could be a faulty pressure switch or a problem with the motor. That’s when you don’t want to mess around—electricity and waste don’t mix. We always tell our customers that if it’s not one of the simple fixes above, call a licensed technician, but if you’ve got a pump from us, we offer 24/7 customer support for any questions, no matter how small.
Wait, I should mention a common mistake people make that causes running toilet pumps, too: flushing non-toilet items. I know, it seems obvious, but people flush cotton swabs, dental floss, even baby wipes (even the ones labeled “flushable” — they’re not, and they clump up in these pumps way more than regular toilet paper). That’s why we always include a little fact sheet with every pump we sell saying “no flushing anything except toilet paper and human waste” — it saves everyone a headache.
Let me circle back to Maria, because that’s exactly what happened. Her 4-year-old flushed a handful of cotton swabs a week before her pump seized, and they got stuck in the impeller, causing it to lock up. The humming noise she heard was the motor working as hard as it could to turn the seized impeller, which is exactly the “running” she called about. By the time I got there, I showed her how to lift the pump, remove the impeller cover, take out the cotton swabs, and spin it freely. She flushed a test cycle, it worked, and she’s now got a spare impeller in her linen closet just in case.
For our business, this is why we focus on not just selling pumps, but helping our customers take care of them. A lot of pump suppliers just ship the unit and disappear, but we’re here for the whole lifecycle. If you’re a homeowner dealing with a running toilet pump, the first step is always the simple checks: power off, check the float, clear small clogs, free the impeller. If that doesn’t work, we’re here to help with troubleshooting, replacement parts, or technical support whenever you need it.
If you’ve tried these steps and your toilet pump is still running, or you’re not comfortable doing any of these checks, our team is ready to connect you to our network of licensed service professionals, or you can reach out to our sales team to chat about replacement parts, impeller kits, or even a new pump if your current one is old. We stock all the common replacement parts for the most popular toilet pump models, and most orders are delivered in 2 business days, so you don’t have to wait around for a plumber or a new unit.
Just to recap the quick, step-by-step checklist to keep your toilet pump from running nonstop: 1. Power off the pump and water supply. 2. Check the float for sticking, clean or lube if needed. 3. Clear any small clogs from the inlet or check valve. 4. Free a seized impeller with warm water and soap. 5. Test before restoring power. That’s it—most fixes take 15-20 minutes, no special tools needed, and no need to call a plumber for the small stuff.
At the end of the day, a running toilet pump isn’t a sign that your home is broken—it’s a tiny reminder that even the most reliable systems need a little basic maintenance. We’ve been supplying pumps to residential and commercial customers for over a decade, and the number one thing we hear from people who buy from us is that they never have to deal with the surprise plumbing disasters that come with flimsy, cheap pumps. We build our units to last, and we back that up with support for every step of owning one.

If you’re a homeowner dealing with a running toilet pump, or a property manager looking for reliable pumps for multiple units, don’t hesitate to reach out to our team to discuss your needs. Whether you need a replacement part, a troubleshooting question answered, or a quote for bulk orders, we’re here to help you keep your plumbing running smoothly, no weekend crises required.
Rotary Scrubber References
- Plumbing-Heating-Cooling Contractors Association. (2021). Residential Sump and Toilet Pump Maintenance Guide. National Trade and Professional Association for the PHCC Industry.
- Macerating Toilet Systems: Installation, Operation, and Troubleshooting. (2020). International Association of Plumbing and Mechanical Officials (IAPMO).
- Pump Maintenance Best Practices for Residential Waste Systems. (2022). American Water Works Association (AWWA).
Jiangxi Well-tech International Mining Equipment Co., Ltd.
Jiangxi Well-tech International Mining Equipment Co., Ltd. is one of the most professional pump manufacturers and suppliers in China, featured by quality products and good service. Please rest assured to wholesale customized pump at competitive price from our factory.
Address: Guzhang Industrial Park of Shicheng County, Ganzhou City, Jiangxi Province, China
E-mail: mily@benefication.com
WebSite: https://www.cn-welltech.com/